And for me it didn't work as you can see below.
John
> John,
>
> Yup, it does work, even with that line feed in the middle.
> I'm not sure why it does come through as a hyperlink.
>
> Rick
>
> Thanks. Didn't know that. Of course I just have to try it
> too. <GRIN>
>
> <http://groups.yahoo.com/group/gingery_machines/photos/album/1
> 572960416/pi
> c/list>
>
>
> John
>
> Automation Artisans Inc.
> http://www.autoartisans.com/ELS/
> Ph. 1 250 544 4950
>
>
> > -----Original Message-----
> > From: gingery_machines@yahoogroups.com
> > [mailto:gingery_machines@yahoogroups.com] On Behalf Of Wonk
> > Sent: Thursday, July 21, 2011 3:08 PM
> > To: gingery_machines@yahoogroups.com
> > Subject: [gingery_machines] Re: new article available: An
> Experimental
> > Way toStatically Balance a Bench Grinder
> >
> >
> >
> > John,
> >
> > If you place a < at the start of a link and a > at the end it won't
> > matter if there is wrap around of your link and it will
> load without
> > an error!
> >
> > Thanks Wonk
> >
> >
> > --- In gingery_machines@yahoogroups.com, "John Dammeyer"
> <johnd@...>
> > wrote:
> > >
> > > Hi Rick,
> > >
> > > My shaft was machined well enough that I could extend the
> > backing plate.
> > > But if it made any difference I don't know.
> > >
> > > I have accumulated a number of different 'pulley' patterns
> > over the years
> > > that lend themselves well to this sort of project. The
> > sprue placed on
> > > the back then gives me what I need. In this case I think I
> > too removed a
> > > bit of metal all told.
> > >
> > > With the furnace and the ability (and enjoyment) of making
> > patterns I have
> > > a tendency to look at everything as a nail. If you recall
> > the expression:
> > > "When all you have is a hammer everything begins to look
> > like a nail". So
> > > I tend to design and build patterns for things and then
> > cast. Partly
> > > because $1.50 worth of propane is far less expensive
> > compared with $20
> > > worth of 6061 plate. But it comes at the price of projects
> > taking far
> > > longer than needed.
> > >
> > > That's why it took so long to mount the stepper motor on my
> > mill knee.
> > > But when I finally did cast the motor mount plate it's true
> > my costs were
> > > minimal if labour isn't factored into it. And now I can
> > use an ELS to
> > > move the knee up and down. When I get around to having
> > enough Tormach
> > > tooling to identify them with a tool # and Z offset I'll be
> > able to lower
> > > the knee, insert a new tool and have the knee move
> > automatically back up
> > > so the tip of the tool is a known distance from the work.
> > >
> > > Photos of the casting and the end product here:
> > >
> > http://groups.yahoo.com/group/gingery_machines/photos/album/15
> > 72960416/pic
> > > /list
> > >
> > > But first, patterns to make for the X and Y axis motor and
> > bearing mounts
> > > along with some way of cleanly moving the mill quill down
> > with a motor.
> > > There will be lots more castings.
> > >
> > > John
> > >
> > > >
> > > > John,
> > > >
> > > > My design is almost identical to yours. I just didn't
> extend the
> > > > backing washer beyond the step on the spindle because the metal
> > > > was poorly machined in that area.
> > > >
> > > > On a related note, being able to turn out small, quick castings
> > > > like this sounds really great. Hopefully I will be starting to
> > > > build a little furnace soon based on CT2's advice. It really
> > > > bugged me to hog out so much metal to go from 2" OD
> down to 1" OD.
> > > >
> > >
> >
> >
> >
> >
> > ------------------------------------
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
>
>
>
> ------------------------------------
>
> Yahoo! Groups Links
>
>
>
>
>
>
> ------------------------------------
>
> Yahoo! Groups Links
>
>
>
>
http://groups.yahoo.com/group/gingery_machines/app/peoplemap/view/map
No comments:
Post a Comment